Influence of aggregates on chloride diffusion coefficient into mortar

In order to determine the influence of aggregates on chloride ion ingress, mortar specimens were cast with different aggregate size distribution and the same aggregate volume content. One side of the specimen was in contact with alkaline solution containing sodium chloride. The process of chloride ingress is due to diffusion. The effect of the interfacial transition zone (ITZ) around aggregate and of the tortuosity due to aggregates have been taken into account for interpreting the experimental data obtained. These two competing effects have been quantified by using the theory of composite materials. It appears that the diffusion coefficient varies as a function of the ITZ volume content and of the tortuosity.     

跨国化工企业在我国的投资现状

由于市场、人力资源及成本的优势,跨过公司在我国的投资不断增加,我国已成为全球研发投资项目的最大积聚地。介绍了近几年跨国化工企业在我国投资的项目情况,新一轮的投资主要集中在长江三角洲地区。随着众多跨国公司的签约,催生了南京化学工业园区、上海化学工业区、泉州泉港石化工业区,惠州大亚湾石油化学工业区,同时也将一体化基地的理念带入中国。     

一种检测单晶炉热场温度的新方法

为去除单晶炉热场温度测量信号中的低频干扰、提高温度信号的估计精度,本文提出了一种基于跨维模拟退火(trans dimensional simulated annealing,TDSA)的单晶炉热场温度检测方法.该方法首先将AIC(Akaike information criterion)信号个数判断准则纳入采样机制中以便对干扰个数采样估计,进而利用所设计的基于信号频谱和轮盘赌思想的Metropolis Hastings机制对相应个数的干扰频率进行采样,最后设计了混合均匀和高斯采样机制对单晶炉热场温度进行采样估计.仿真和单晶炉工程实验结果表明,该方法在干扰个数未知的情况下,能够有效地抑制低频干扰、准确检测单晶炉热场的温度.     

5’-单磷酸腺苷在乙醇-水中介稳区性质研究

针对5’-单磷酸腺苷(5’-AMP)在溶析结晶中易出现爆发结晶的问题,分别采用静态法和激光法测定了293—323 K下5’-AMP在纯水以及溶剂体积比为0.3—2.0的乙醇-水体系中的溶解度和超溶解度,以指数经验关联式建立了超溶解度关联式,并在试验条件下考察了温度、乙醇流速、pH值和搅拌速率对介稳区宽度的影响。运用中心复合设计预测了5’-AMP在本溶析结晶体系中介稳区间,并用扫描电镜观察了5’-AMP在结晶条件优化前后晶体形态的变化情况,为工业生产中提高结晶产品质量提供了理论指导。     

稀土丁异戊橡胶改性天然橡胶的应用研究

采用稀土丁异戊橡胶代替顺丁橡胶，测试并分析了改性天然橡胶的低温性能及相关性能。结果表明，稀土丁异戊橡胶改性的天然橡胶室强力学性能和粘接性能与顺丁橡胶改性的天然橡胶相近，但低温性能有较大的改善。在-40℃下贮存2h后，顶丁橡胶改性天然橡胶硫化胶有明显的结晶现象，其剪切模量较室温下的相应值增加了6倍，而稀土丁异戊橡胶改性的天然橡胶硫化胶保持了良好的弹性，其剪切模量值与室温下的相当。     

Failure load prediction of structural adhesive joints : Part 2: Experimental study

The objective of this study was to determine how the fracture of adhesive joints depends on elastic beam parameters describing the adherends and the applied loads. The basic specimen geometry was the cracked lap shear joint constructed of aluminium alloy with various adherend and bondline thicknesses. Loads were applied in different combinations of bending, tension and shear to generate a failure envelope for each adhesive and specimen geometry. It was found that crack propagation for precracked specimens occured at a critical strain energy release rate but was also a function of the G_I/G_II ratio and the bondline thickness. The experiments also showed that the loads required to propagate a crack in a precracked specimen were always lower than the loads required to break the fillet. Hence, by treating uncracked joints as being cracked, where the fictitious crack tip is assumed to coincide with the location of the fillet, a conservative estimate of the failure load is obtained.     

基于数字式红外传感器的姿态测量盲区补偿法

单轴红外姿态测量系统在测量小型无人机姿态角时存在盲区,通过增加一组与原轴线相垂直的红外传感器,形成双轴姿态测量系统,对盲区进行补偿。两组红外传感器一定有一组位于倾角可测区域,通过测试目标轴的输出温差的大小,判断位于可测区域的轴线,可实现对目标轴姿态角的解算。首次采用数字式输出红外热电堆传感器设计实现了180°无盲区的姿态角测量模块,经过测试,其静态误差小于2°。     

Shear Strength of Pressure Sensitive Adhesives and its Correlation to Mechanical Properties

Correlations between shear resistance and the mechanical properties of pressure sensitive adhesives are studied by measuring the deformation behaviour in the static and the dynamic shear test and determining the dynamic shear modulus of the adhesive. For polymers with low or moderate viscosities, the shear strain vs. time characteristics in a static shear test and, accordingly, the static shear strength, can be evaluated from the master curves of the dynamic shear modulus or the dynamic viscosity. The dynamic shear strength also can be calculated. These exact calculations cannot be applied to highly viscous or slightly crosslinked polymers. On the basis of the model experiments, empirical correlations between shear strength and the dynamic shear modulus are established which seem to be generally valid.     

纳米蒙脱土/环氧树脂胶粘剂制备工艺优化选择

介绍了制备纳米蒙脱土/环氧树脂胶粘剂的方法,并通过正交试验的方法分析了固化时间、固化温度、搅拌时间、搅拌温度对纳米蒙脱土/环氧树脂胶粘涂层拉伸剪切强度的影响,给出了上述四个工艺参数的最佳工艺规范并通过试验验证了结论。     

保护胶体稳定的丙烯酸酯乳液流变性

分别采用常规乳化剂和羟乙基纤维素为保护胶体制备丙烯酸酯乳液。通过TEM分别观察乳胶粒的形态。利用流变仪测定剪切速率（Ds）-剪切应力（τ）关系、剪切速率（Ds）-黏度（η）关系。结果表明：采用羟乙基纤维素为保护胶体制备的乳液与常规乳液具有不同结构，该结构使其乳液体系流变性能不同。在相同剪切速率下，保护胶体制备的丙烯酸酯乳液的剪切力明显大于常规乳液的剪切力，该乳液在一定剪切速率范围内有剪切稀化现象。